SCPH-1002 PSU fuse continue to blow.

Post a topic about yourself to let others know your skills, hobbies, etc.
Post Reply
User avatar
~PSXLoVeR95~
Verified
Active PSXDEV User
Active PSXDEV User
Posts: 73
Joined: Sep 18, 2016
I am a: Huge lover of PS1

SCPH-1002 PSU fuse continue to blow.

Post by ~PSXLoVeR95~ » September 21st, 2016, 9:27 pm

Hi there!
I have a problem with my 1002 PSU (received yesterday...after try to repairing my 1000 :evil: ) and i resolder all the pads with a nice and fresh soldering but the fuse...still blow!
It's a EAMX5 aka NPX-029E1-1A (so a Matsushita PSU) and aestheticallyit's in good condition ....
Here some pic :

Image
Image
Probably the problem is in the live section, but i'm not sure :mrgreen: !
Thanks in advance !
~ My PS Collection ~
4x SCPH-1000
2x SCPH-1001
7x SCPH-1002
1x SCPH-3000
1x SCPH-3500
1x SCPH-5000
1x SCPH-5501
1x SCPH-5502
2x SCPH-7000
2x SCPH-7002
1x SCPH-7500
1x SCPH-7501
2x SCPH-9000
1x SCPH-9002
3x SCPH-102
>>IT'S A SONY
Top
User avatar
Shadow
Verified
Admin / PSXDEV
Admin / PSXDEV
Posts: 2670
Joined: Dec 31, 2012
PlayStation Model: H2000/5502
Discord: Shadow^PSXDEV

Post by Shadow » September 21st, 2016, 9:29 pm

Did the fuse blow when the secondary side was turned off (not powering the PSX)?
Development Console: SCPH-5502 with 8MB RAM, MM3 Modchip, PAL 60 Colour Modification (for NTSC), PSIO Switch Board, DB-9 breakout headers for both RGB and Serial output and an Xplorer with CAETLA 0.34.

PlayStation Development PC: Windows 98 SE, Pentium 3 at 400MHz, 128MB SDRAM, DTL-H2000, DTL-H2010, DTL-H201A, DTL-S2020 (with 4GB SCSI-2 HDD), 21" Sony G420, CD-R burner, 3.25" and 5.25" Floppy Diskette Drives, ZIP 100 Diskette Drive and an IBM Model M keyboard.
Top
User avatar
~PSXLoVeR95~
Verified
Active PSXDEV User
Active PSXDEV User
Posts: 73
Joined: Sep 18, 2016
I am a: Huge lover of PS1

Post by ~PSXLoVeR95~ » September 21st, 2016, 9:55 pm

Hi shadow :) !
Well, the fuse blow when i just plugged the AC cable. the PSU isn't plug with the motherboard yet :/...
I've only two 250v 1.6AH fuse.... :(
So, i've only two chances XD
~ My PS Collection ~
4x SCPH-1000
2x SCPH-1001
7x SCPH-1002
1x SCPH-3000
1x SCPH-3500
1x SCPH-5000
1x SCPH-5501
1x SCPH-5502
2x SCPH-7000
2x SCPH-7002
1x SCPH-7500
1x SCPH-7501
2x SCPH-9000
1x SCPH-9002
3x SCPH-102
>>IT'S A SONY
Top
User avatar
Shadow
Verified
Admin / PSXDEV
Admin / PSXDEV
Posts: 2670
Joined: Dec 31, 2012
PlayStation Model: H2000/5502
Discord: Shadow^PSXDEV

Post by Shadow » September 22nd, 2016, 3:43 pm

The transformer could be bad or the choke could be bad. It could also be the primary filtration capacitors. You'll have to get a multi-meter and start testing components because that's the only way you'll figure out where the short is occurring.
Development Console: SCPH-5502 with 8MB RAM, MM3 Modchip, PAL 60 Colour Modification (for NTSC), PSIO Switch Board, DB-9 breakout headers for both RGB and Serial output and an Xplorer with CAETLA 0.34.

PlayStation Development PC: Windows 98 SE, Pentium 3 at 400MHz, 128MB SDRAM, DTL-H2000, DTL-H2010, DTL-H201A, DTL-S2020 (with 4GB SCSI-2 HDD), 21" Sony G420, CD-R burner, 3.25" and 5.25" Floppy Diskette Drives, ZIP 100 Diskette Drive and an IBM Model M keyboard.
Top
User avatar
~PSXLoVeR95~
Verified
Active PSXDEV User
Active PSXDEV User
Posts: 73
Joined: Sep 18, 2016
I am a: Huge lover of PS1

Post by ~PSXLoVeR95~ » September 23rd, 2016, 12:40 am

Yeaaah Shadow, i did it!!!
I just check the FS2KM (high speed MITSUBISHI MOSFET) beacause was in short and change the main capacitor for safety (400V 47uf). It works perfectly :)!
But on the pinout i have 7,0vdc and not 7,5vdc...the console working fine but i'm don't know if it's normal XD!
~ My PS Collection ~
4x SCPH-1000
2x SCPH-1001
7x SCPH-1002
1x SCPH-3000
1x SCPH-3500
1x SCPH-5000
1x SCPH-5501
1x SCPH-5502
2x SCPH-7000
2x SCPH-7002
1x SCPH-7500
1x SCPH-7501
2x SCPH-9000
1x SCPH-9002
3x SCPH-102
>>IT'S A SONY
Top
User avatar
Shadow
Verified
Admin / PSXDEV
Admin / PSXDEV
Posts: 2670
Joined: Dec 31, 2012
PlayStation Model: H2000/5502
Discord: Shadow^PSXDEV

Post by Shadow » September 23rd, 2016, 2:35 am

~PSXLoVeR95~ wrote:Yeaaah Shadow, i did it!!!
I just check the FS2KM (high speed MITSUBISHI MOSFET) beacause was in short.
But on the pinout i have 7,0vdc and not 7,5vdc...the console working fine but i'm don't know if it's normal XD!
Ah, it would have been the FET. Make sure you put the heatsink back on it!

There is a pot you can adjust on the secondary side to calibrate the voltage.
I think the older 1000 series PSU's outputted a lower 7V rail anyway.
Development Console: SCPH-5502 with 8MB RAM, MM3 Modchip, PAL 60 Colour Modification (for NTSC), PSIO Switch Board, DB-9 breakout headers for both RGB and Serial output and an Xplorer with CAETLA 0.34.

PlayStation Development PC: Windows 98 SE, Pentium 3 at 400MHz, 128MB SDRAM, DTL-H2000, DTL-H2010, DTL-H201A, DTL-S2020 (with 4GB SCSI-2 HDD), 21" Sony G420, CD-R burner, 3.25" and 5.25" Floppy Diskette Drives, ZIP 100 Diskette Drive and an IBM Model M keyboard.
Top
User avatar
~PSXLoVeR95~
Verified
Active PSXDEV User
Active PSXDEV User
Posts: 73
Joined: Sep 18, 2016
I am a: Huge lover of PS1

Post by ~PSXLoVeR95~ » September 23rd, 2016, 4:36 am

Aye :)
Heatsink + a little of thermal paste, but just a little :)!
Ah okay, now i know what is that pot....i leave for that voltage.
For curiosity, what happen if i reduce too much the voltage of PSU in DC?
Thanks !
~ My PS Collection ~
4x SCPH-1000
2x SCPH-1001
7x SCPH-1002
1x SCPH-3000
1x SCPH-3500
1x SCPH-5000
1x SCPH-5501
1x SCPH-5502
2x SCPH-7000
2x SCPH-7002
1x SCPH-7500
1x SCPH-7501
2x SCPH-9000
1x SCPH-9002
3x SCPH-102
>>IT'S A SONY
Top
User avatar
Shadow
Verified
Admin / PSXDEV
Admin / PSXDEV
Posts: 2670
Joined: Dec 31, 2012
PlayStation Model: H2000/5502
Discord: Shadow^PSXDEV

Post by Shadow » September 23rd, 2016, 3:16 pm

The PSX regulators will fail to switch states and it simply won't power on.
Development Console: SCPH-5502 with 8MB RAM, MM3 Modchip, PAL 60 Colour Modification (for NTSC), PSIO Switch Board, DB-9 breakout headers for both RGB and Serial output and an Xplorer with CAETLA 0.34.

PlayStation Development PC: Windows 98 SE, Pentium 3 at 400MHz, 128MB SDRAM, DTL-H2000, DTL-H2010, DTL-H201A, DTL-S2020 (with 4GB SCSI-2 HDD), 21" Sony G420, CD-R burner, 3.25" and 5.25" Floppy Diskette Drives, ZIP 100 Diskette Drive and an IBM Model M keyboard.
Top
User avatar
~PSXLoVeR95~
Verified
Active PSXDEV User
Active PSXDEV User
Posts: 73
Joined: Sep 18, 2016
I am a: Huge lover of PS1

Post by ~PSXLoVeR95~ » September 23rd, 2016, 9:35 pm

Interesting, shadow! :)
It's a shame that the other power supplies doesn't have this pot :(
~ My PS Collection ~
4x SCPH-1000
2x SCPH-1001
7x SCPH-1002
1x SCPH-3000
1x SCPH-3500
1x SCPH-5000
1x SCPH-5501
1x SCPH-5502
2x SCPH-7000
2x SCPH-7002
1x SCPH-7500
1x SCPH-7501
2x SCPH-9000
1x SCPH-9002
3x SCPH-102
>>IT'S A SONY
Top
Post Reply

Return to “General Chat & Messaging”

Who is online

Users browsing this forum: No registered users and 3 guests