SCPH-1002 PSU fuse continue to blow.
-
~PSXLoVeR95~ Verified
- Active PSXDEV User
- Posts: 73
- Joined: Sep 18, 2016
- I am a: Huge lover of PS1
SCPH-1002 PSU fuse continue to blow.
Hi there!
I have a problem with my 1002 PSU (received yesterday...after try to repairing my 1000 ) and i resolder all the pads with a nice and fresh soldering but the fuse...still blow!
It's a EAMX5 aka NPX-029E1-1A (so a Matsushita PSU) and aestheticallyit's in good condition ....
Here some pic :
Probably the problem is in the live section, but i'm not sure !
Thanks in advance !
I have a problem with my 1002 PSU (received yesterday...after try to repairing my 1000 ) and i resolder all the pads with a nice and fresh soldering but the fuse...still blow!
It's a EAMX5 aka NPX-029E1-1A (so a Matsushita PSU) and aestheticallyit's in good condition ....
Here some pic :
Probably the problem is in the live section, but i'm not sure !
Thanks in advance !
~ My PS Collection ~
4x SCPH-1000
2x SCPH-1001
7x SCPH-1002
1x SCPH-3000
1x SCPH-3500
1x SCPH-5000
1x SCPH-5501
1x SCPH-5502
2x SCPH-7000
2x SCPH-7002
1x SCPH-7500
1x SCPH-7501
2x SCPH-9000
1x SCPH-9002
3x SCPH-102
>>IT'S A SONY
4x SCPH-1000
2x SCPH-1001
7x SCPH-1002
1x SCPH-3000
1x SCPH-3500
1x SCPH-5000
1x SCPH-5501
1x SCPH-5502
2x SCPH-7000
2x SCPH-7002
1x SCPH-7500
1x SCPH-7501
2x SCPH-9000
1x SCPH-9002
3x SCPH-102
>>IT'S A SONY
-
Shadow Verified
- Admin / PSXDEV
- Posts: 2670
- Joined: Dec 31, 2012
- PlayStation Model: H2000/5502
- Discord: Shadow^PSXDEV
Did the fuse blow when the secondary side was turned off (not powering the PSX)?
Development Console: SCPH-5502 with 8MB RAM, MM3 Modchip, PAL 60 Colour Modification (for NTSC), PSIO Switch Board, DB-9 breakout headers for both RGB and Serial output and an Xplorer with CAETLA 0.34.
PlayStation Development PC: Windows 98 SE, Pentium 3 at 400MHz, 128MB SDRAM, DTL-H2000, DTL-H2010, DTL-H201A, DTL-S2020 (with 4GB SCSI-2 HDD), 21" Sony G420, CD-R burner, 3.25" and 5.25" Floppy Diskette Drives, ZIP 100 Diskette Drive and an IBM Model M keyboard.
PlayStation Development PC: Windows 98 SE, Pentium 3 at 400MHz, 128MB SDRAM, DTL-H2000, DTL-H2010, DTL-H201A, DTL-S2020 (with 4GB SCSI-2 HDD), 21" Sony G420, CD-R burner, 3.25" and 5.25" Floppy Diskette Drives, ZIP 100 Diskette Drive and an IBM Model M keyboard.
-
~PSXLoVeR95~ Verified
- Active PSXDEV User
- Posts: 73
- Joined: Sep 18, 2016
- I am a: Huge lover of PS1
Hi shadow !
Well, the fuse blow when i just plugged the AC cable. the PSU isn't plug with the motherboard yet :/...
I've only two 250v 1.6AH fuse....
So, i've only two chances XD
Well, the fuse blow when i just plugged the AC cable. the PSU isn't plug with the motherboard yet :/...
I've only two 250v 1.6AH fuse....
So, i've only two chances XD
~ My PS Collection ~
4x SCPH-1000
2x SCPH-1001
7x SCPH-1002
1x SCPH-3000
1x SCPH-3500
1x SCPH-5000
1x SCPH-5501
1x SCPH-5502
2x SCPH-7000
2x SCPH-7002
1x SCPH-7500
1x SCPH-7501
2x SCPH-9000
1x SCPH-9002
3x SCPH-102
>>IT'S A SONY
4x SCPH-1000
2x SCPH-1001
7x SCPH-1002
1x SCPH-3000
1x SCPH-3500
1x SCPH-5000
1x SCPH-5501
1x SCPH-5502
2x SCPH-7000
2x SCPH-7002
1x SCPH-7500
1x SCPH-7501
2x SCPH-9000
1x SCPH-9002
3x SCPH-102
>>IT'S A SONY
-
Shadow Verified
- Admin / PSXDEV
- Posts: 2670
- Joined: Dec 31, 2012
- PlayStation Model: H2000/5502
- Discord: Shadow^PSXDEV
The transformer could be bad or the choke could be bad. It could also be the primary filtration capacitors. You'll have to get a multi-meter and start testing components because that's the only way you'll figure out where the short is occurring.
Development Console: SCPH-5502 with 8MB RAM, MM3 Modchip, PAL 60 Colour Modification (for NTSC), PSIO Switch Board, DB-9 breakout headers for both RGB and Serial output and an Xplorer with CAETLA 0.34.
PlayStation Development PC: Windows 98 SE, Pentium 3 at 400MHz, 128MB SDRAM, DTL-H2000, DTL-H2010, DTL-H201A, DTL-S2020 (with 4GB SCSI-2 HDD), 21" Sony G420, CD-R burner, 3.25" and 5.25" Floppy Diskette Drives, ZIP 100 Diskette Drive and an IBM Model M keyboard.
PlayStation Development PC: Windows 98 SE, Pentium 3 at 400MHz, 128MB SDRAM, DTL-H2000, DTL-H2010, DTL-H201A, DTL-S2020 (with 4GB SCSI-2 HDD), 21" Sony G420, CD-R burner, 3.25" and 5.25" Floppy Diskette Drives, ZIP 100 Diskette Drive and an IBM Model M keyboard.
-
~PSXLoVeR95~ Verified
- Active PSXDEV User
- Posts: 73
- Joined: Sep 18, 2016
- I am a: Huge lover of PS1
Yeaaah Shadow, i did it!!!
I just check the FS2KM (high speed MITSUBISHI MOSFET) beacause was in short and change the main capacitor for safety (400V 47uf). It works perfectly !
But on the pinout i have 7,0vdc and not 7,5vdc...the console working fine but i'm don't know if it's normal XD!
I just check the FS2KM (high speed MITSUBISHI MOSFET) beacause was in short and change the main capacitor for safety (400V 47uf). It works perfectly !
But on the pinout i have 7,0vdc and not 7,5vdc...the console working fine but i'm don't know if it's normal XD!
~ My PS Collection ~
4x SCPH-1000
2x SCPH-1001
7x SCPH-1002
1x SCPH-3000
1x SCPH-3500
1x SCPH-5000
1x SCPH-5501
1x SCPH-5502
2x SCPH-7000
2x SCPH-7002
1x SCPH-7500
1x SCPH-7501
2x SCPH-9000
1x SCPH-9002
3x SCPH-102
>>IT'S A SONY
4x SCPH-1000
2x SCPH-1001
7x SCPH-1002
1x SCPH-3000
1x SCPH-3500
1x SCPH-5000
1x SCPH-5501
1x SCPH-5502
2x SCPH-7000
2x SCPH-7002
1x SCPH-7500
1x SCPH-7501
2x SCPH-9000
1x SCPH-9002
3x SCPH-102
>>IT'S A SONY
-
Shadow Verified
- Admin / PSXDEV
- Posts: 2670
- Joined: Dec 31, 2012
- PlayStation Model: H2000/5502
- Discord: Shadow^PSXDEV
Ah, it would have been the FET. Make sure you put the heatsink back on it!~PSXLoVeR95~ wrote:Yeaaah Shadow, i did it!!!
I just check the FS2KM (high speed MITSUBISHI MOSFET) beacause was in short.
But on the pinout i have 7,0vdc and not 7,5vdc...the console working fine but i'm don't know if it's normal XD!
There is a pot you can adjust on the secondary side to calibrate the voltage.
I think the older 1000 series PSU's outputted a lower 7V rail anyway.
Development Console: SCPH-5502 with 8MB RAM, MM3 Modchip, PAL 60 Colour Modification (for NTSC), PSIO Switch Board, DB-9 breakout headers for both RGB and Serial output and an Xplorer with CAETLA 0.34.
PlayStation Development PC: Windows 98 SE, Pentium 3 at 400MHz, 128MB SDRAM, DTL-H2000, DTL-H2010, DTL-H201A, DTL-S2020 (with 4GB SCSI-2 HDD), 21" Sony G420, CD-R burner, 3.25" and 5.25" Floppy Diskette Drives, ZIP 100 Diskette Drive and an IBM Model M keyboard.
PlayStation Development PC: Windows 98 SE, Pentium 3 at 400MHz, 128MB SDRAM, DTL-H2000, DTL-H2010, DTL-H201A, DTL-S2020 (with 4GB SCSI-2 HDD), 21" Sony G420, CD-R burner, 3.25" and 5.25" Floppy Diskette Drives, ZIP 100 Diskette Drive and an IBM Model M keyboard.
-
~PSXLoVeR95~ Verified
- Active PSXDEV User
- Posts: 73
- Joined: Sep 18, 2016
- I am a: Huge lover of PS1
Aye
Heatsink + a little of thermal paste, but just a little !
Ah okay, now i know what is that pot....i leave for that voltage.
For curiosity, what happen if i reduce too much the voltage of PSU in DC?
Thanks !
Heatsink + a little of thermal paste, but just a little !
Ah okay, now i know what is that pot....i leave for that voltage.
For curiosity, what happen if i reduce too much the voltage of PSU in DC?
Thanks !
~ My PS Collection ~
4x SCPH-1000
2x SCPH-1001
7x SCPH-1002
1x SCPH-3000
1x SCPH-3500
1x SCPH-5000
1x SCPH-5501
1x SCPH-5502
2x SCPH-7000
2x SCPH-7002
1x SCPH-7500
1x SCPH-7501
2x SCPH-9000
1x SCPH-9002
3x SCPH-102
>>IT'S A SONY
4x SCPH-1000
2x SCPH-1001
7x SCPH-1002
1x SCPH-3000
1x SCPH-3500
1x SCPH-5000
1x SCPH-5501
1x SCPH-5502
2x SCPH-7000
2x SCPH-7002
1x SCPH-7500
1x SCPH-7501
2x SCPH-9000
1x SCPH-9002
3x SCPH-102
>>IT'S A SONY
-
Shadow Verified
- Admin / PSXDEV
- Posts: 2670
- Joined: Dec 31, 2012
- PlayStation Model: H2000/5502
- Discord: Shadow^PSXDEV
The PSX regulators will fail to switch states and it simply won't power on.
Development Console: SCPH-5502 with 8MB RAM, MM3 Modchip, PAL 60 Colour Modification (for NTSC), PSIO Switch Board, DB-9 breakout headers for both RGB and Serial output and an Xplorer with CAETLA 0.34.
PlayStation Development PC: Windows 98 SE, Pentium 3 at 400MHz, 128MB SDRAM, DTL-H2000, DTL-H2010, DTL-H201A, DTL-S2020 (with 4GB SCSI-2 HDD), 21" Sony G420, CD-R burner, 3.25" and 5.25" Floppy Diskette Drives, ZIP 100 Diskette Drive and an IBM Model M keyboard.
PlayStation Development PC: Windows 98 SE, Pentium 3 at 400MHz, 128MB SDRAM, DTL-H2000, DTL-H2010, DTL-H201A, DTL-S2020 (with 4GB SCSI-2 HDD), 21" Sony G420, CD-R burner, 3.25" and 5.25" Floppy Diskette Drives, ZIP 100 Diskette Drive and an IBM Model M keyboard.
-
~PSXLoVeR95~ Verified
- Active PSXDEV User
- Posts: 73
- Joined: Sep 18, 2016
- I am a: Huge lover of PS1
Interesting, shadow!
It's a shame that the other power supplies doesn't have this pot
It's a shame that the other power supplies doesn't have this pot
~ My PS Collection ~
4x SCPH-1000
2x SCPH-1001
7x SCPH-1002
1x SCPH-3000
1x SCPH-3500
1x SCPH-5000
1x SCPH-5501
1x SCPH-5502
2x SCPH-7000
2x SCPH-7002
1x SCPH-7500
1x SCPH-7501
2x SCPH-9000
1x SCPH-9002
3x SCPH-102
>>IT'S A SONY
4x SCPH-1000
2x SCPH-1001
7x SCPH-1002
1x SCPH-3000
1x SCPH-3500
1x SCPH-5000
1x SCPH-5501
1x SCPH-5502
2x SCPH-7000
2x SCPH-7002
1x SCPH-7500
1x SCPH-7501
2x SCPH-9000
1x SCPH-9002
3x SCPH-102
>>IT'S A SONY
Who is online
Users browsing this forum: No registered users and 6 guests